Highly polluted urban storm water from e.g. highways can contain large amounts of heavy metals that may cause harm if they are discharged into recipients. To remove the heavy metals a possible low-cost method that does not require much maintenance, could be the use of reactive filters with filter materials consisting of industrial residues or other cheap mineral based materials. Dissolved metal ions are removed by reactive filters through the processes of ions binding to active sites on the surface of the filter materials, or by formation of insoluble precipitates.The ability of CaO-treated granulated blast-furnace slag, iron oxide coated sand, olivine and nepheline to remove seven heavy metals (Cr, Cd, Cu, Ni, Zn, Pb and Hg) from urban storm water was studied. Initially batch experiments were performed where the effect of pH, dissolved organic carbon (DOC) and dissolved ions on the adsorption efficiency was studied.

Discharge of untreated wastewater leads to unnaturally high levels of nitrogen and phosphorus in rivers, lakes and the sea, which results in unbalanced ecosystems with eutrophication and lack of oxygen. Part of the phosphorus in surface waters is coming from on-site wastewater treatment from scattered households with unsatisfactory purification. Blast furnace slag is a by-product from iron production, and has in laboratory trials showed good phosphorus binding capacity. To test blast furnace slag as a reactive filter media for phosphorus separation in a full scale experiment, a wastewater treatment plant has been built behind the picnic area at Ångersjön alongside the road E4 in central-eastern Sweden. The plant contains two parallel lines, one with blast furnaces slag and the other with Filtralite-P as phosphorus sorbent. Both filters have showed decreasing phosphorus purification effect with time in spite of a low wastewater load.

An excessive input of nutrients to lakes and other water bodies has created a problem with eutrophication in Sweden. Untreated, or partially treated, domestic sewage is a major source for discharge of phosphorus (P), which is the nutrient most frequently responsible for eutrophication of most fresh waters and the Baltic Sea. The waste water can be cleaned by filter materials, which have a high P-retention ability and which after saturation may be used as fertilizers. Four potentially suitable filter materials were tested in batch- and column experiments in this study. In the batch experiments, the following materials were shaken with waste water in time series ranging from 5 seconds to 60 minutes: coarse (1-4 mm) and fine (0-2 mm) Polonite® (heated bedrock from Poland); Filtralite® (light expanded clay aggregates with limestone added before burning); water cooled blast furnace slag (BF-slag) and BF-slag mixed with 10% burned limestone.

Four different kinds of filter-materials with reactive surfaces have been studied concerning their capacity to absorb heavy metals in leachate from a municipal waste deposit. The heavy metals studied were: lead, cadmium, copper, mercury, chromium, nickel and zinc. The leachate contains high levels of dissolved organic carbon (DOC) and has a high pH-value along with a high buffer capacity. These characteristics of the leachate make it difficult to remove pollutants and require efficient filters. The filters that were examined in the report are blast-furnace slag with CaO, sand covered with iron oxides, olivine and nepheline.

Betong är vårt vanligaste byggmaterial men cement står globalt sett för 5 % av CO2-emissionerna. Med detta som bakgrund så har CBI Betonginstitutet anordnat en tävling, där målet är att nå den högsta tryckhållfasthet i en resurssnål betong, med enbart 200 kg cement per m3. Syftet med denna rapport är att utvärdera tävlingen, vilket har utförts genom en omfattande litteraturstudie. En första analys av de olika betongrecepten medförde att olika grupperingar kunde urskiljas. Ur dessa fanns det tre stycken vars resultat var väldigt bra. ? Concrete Innovation Centre, som med ett lågt vct, stora mängder granulerad masugnsslagg (81 %) och lite silikastoft (5 %), uppnådde en tryckhållfasthet på 80 MPa vid 28 dygn och 95 MPa vid 56 dygn. ? CBI Stockholm, som genom användandet av ulltrafint filler och silikastoft (4,8 %), uppnådde en tryckhållfasthet på 84 MPa vid 28 dygn och 98 MPa vid 56 dygn. ? Thomas Concrete Group som genom att ersätta cementet med en medelmåttig mängd granulerad masugnsslagg (54 %), liten mängd flygaska (9 %), kalkfiller och silikastoft (5 %), uppnådde en tryckhållfasthet på 94 MPa vid 28 dygn och 98 MPa vid 56 dygn. Det finns således tre recept som vidare studier kan vara rättfärdigade på, de tre ovan nämnda. Det bör tilläggas att en imponerande tryckhållfasthet på nästan 100 MPa, kan uppnås i en betong med enbart 200 kg cement per m3. .

In Sweden more than 400 000 private households have not yet sufficient wastewater purification. These effluent is considered as an increasing problem and many onsite purification methods have been studied. In this investigation, the method of reactive bed filters have been tested by column and batch experiments. Five different kinds of filter materials with reactive surfaces have been studied concerning their capacity to absorb ammonium and phosphorus from wastewater. The materials that were examined are Filtra N, wollastonite Filtra P, blast furnace slag and Polonite®.

This master thesis encompasses an inventory of the older industrial community of Gimo. Investigations of the contamination situation for each industrial area were done. A risk classification according to the Swedish Environmental Protection Agency?s ?Method of Surveying Contaminated Sites?, phase one, followed. The risk classification was done on areas of Iron Work, a rockwool industry and a landfill. Gimo have had iron manufacturing from 1615 until 1945. Gimo have had two blast-furnaces and two smithies periodically.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.

Mechanical scaling is one of the most complex operations of all in the mining process. The operators are using both hearing, sight and feel to read the rock and to know where to scale and where to leave. They say they go on gut feeling in great extent, something that comes with experience. The scaling machine is placed into the edge of unsecured and newly blasted rock to hammer off the blocks that has become loose after the blast, but not enough to fall down. It goes without sayingthat it is a risky job.

This report contains a programming improvement work in a LabVIEW? fire testing furnace control system for SP Fire Technology in Borås. Here materials and products behaviour are tested and evaluated, being exposed to fire. For this task, UGNET is being used for control and surveillance of the testing furnace system. System hardware has been updated gradually through the years, while the software has been neglected.

In the fluidized bed furnace at Rönnskärsverken, Skelleftehamn, sulphur-containing ore concentrates are roasted in order to remove about 50% of the sulphur in the incoming ore concentrate. This occurs in order to reach the goal of a matte containing 55% of copper in the following smelting process. At the same time as the ore concentrate is partially roasted pollutions as arsenic, antimony and bismuth are expelled. Earlier made thermodynamic calculations of equilibrium suggested that calcium and magnesium form stable compounds with arsenic and thereby inhibit expellation of arsenic in the fluidized bed furnace, an element that is undesired. The purpose of this thesis work was to gain knowledge of the mechanisms behind the formation of these stable arsenic compounds.

The global climate-change means increasing mean-temperature and higher precipitation in Sweden, which leads to shorter periods of frozen ground in the forest. At the same time the harvesting machines are getting bigger and more powerful. The forest industry aim at an even wood flow, and the ground damage has to be as low as possible. The two biggest causes for ground-damage is the bearing capacity of the forest ground and the ground-pressure of the harvesting machines. The aim of this study was to find out some rules for the machine choice considering ground pressure, when harvesting on ground with low bearing capacity.A field study, using a Valmet 890.3 forwarder, was carried out where different ground pressures and their effect on the ground were tested on two different types of ground.Additionally, an inventory of damaged harvesting grounds was made.

Totally 84 differentially expressed mRNA clones from infective L3 larvae of the parasite Haemonchus contortus, a blood sucking nematode, were analyzed with single strand hybridization assay (SSH). Altogether 79 clones were sequenced, edited, and compared with proteins found via BLAST in GeneBank. The aim was to investigate gene expression and potential protein expression following storage at 5 °C for 32 weeks. mRNA was extracted from fresh and stored L3. The SSH derived products were cloned into E.

At Sandvik Materials Technology, Argon gas is used as furnace atmosphere when heattreating hot rolled wire. Upon heating chromium steel wire, a rich oxidelayer forms on the wire surface. The abstract of this masters thesis is to enhance the understanding of the constitution of the oxidelayers and the influence of the furnace atmosphere. This will be achieved by performing a number of annealing experiments on laboratory level. Also, the aim is to understand the chemical reactions and physical mecanisms controlling the pickling process.

Ground work like blasting, piling and excavation has always had a great influence during the planning phase of a construction project since it can cause damages on adjacent buildings and have severe economic consequences. This thesis deals with how vibrations caused by ground work influence near-by buildings and what methods geotechnicians and construction entrepreneurs use to handle these risks.The purpose of this thesis is to explain risk management in relation to ground work. In order to achieve this I have used a qualitative method by interviewing a geotechnician and a ground work contractor who possess knowledge and experience useful to this thesis. The result shows that vibrations from ground work spread through the ground as seismic waves that cause displacements and packing in the ground visible in adjacent buildings as cracks and subsidence damages. Geotechnicians study ground work vibrations by means of ground investigations and experience from previous projects in order to produce a risk analysis that entrepreneurs can use to reduce damages.